30 Mar
2019
30 Mar
'19
3:07 a.m.
On Wed, Mar 27, 2019 at 7:26 AM bill Ott <billott(a)theotts.org> wrote:
Xboxboy, I am trying to understand your host network
setup. As an example,
here is my firewall network configuration supporting two VM's. It's not
everything, but is what is required to run the VMs.
My brctl on the firewall:
[root@wbofw perl]# brctl show *ID matches mac addr for eth1 and eno1*
bridge name bridge id STP enabled interfaces
eth1 8000.*001e67e0bbd6 * no eno1
vnet0
vnet1
And the ifconfig from the two VMs running on the firewall system.
Thanks for reply:
Here's my host results:
brctl show
bridge name bridge id STP enabled interfaces
virbr0 8000.525400da324e yes virbr0-nic
and here is the guest debian OS
enpos3: flags=4163<UP,BROADCAST,RUNNING,MULTITCAST> mtu 1500
inet 192.168.1.118 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::a00:27ff:fe87:a4b prefixlen 64 scopeid 0x20<link>
ether 08:00:27:87:0a:4b txqueuelen 1000 (Ethernet)
RX packets 1735 bytes 1215954 (1.1Mib)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 594 bytes 44649 (43.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0X10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 262 bytes 60033 (58.5KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 262 bytes 60033 (58.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@yawssys]# ifconfig *(sshing into the vnet0 VM)
note Mac address is
identical to vnet0*
eth1: Link encap:Ethernet HWaddr *FE:54:00:B7:EA:E1*
inet addr:96.10.34.44 Bcast:96.10.34.63 Mask:255.255.255.224
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:108356 errors:0 dropped:0 overruns:0 frame:0
TX packets:168471 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8480160 (8.0 MiB) TX bytes:199696532 (190.4 MiB)
[root@yawssys7]# ifconfig *(sshing into the vnet1 VM) note Mac address is
identical vnet1*
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 96.10.34.50 netmask 255.255.255.224 broadcast 96.10.34.63
inet6 fe80::5054:ff:fee2:af0b prefixlen 64 scopeid 0x20<link>
ether *FE:54:00:e2:af:0b* txqueuelen 1000 (Ethernet)
RX packets 438230 bytes 223232328 (212.8 MiB)
RX errors 0 dropped 14003 overruns 0 frame 0
TX packets 276326 bytes 137199104 (130.8 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
The nomenclature is slightly different on the systems since they are
running different versions of Centos.
I am running KVM virtual machines. They may work differently than your
VM's.
I wanted to see your VM ifconfig to see it they align with your host
interfaces.
Hope this helps.
Regards,
Bill Ott
Home: 919-363-0031
Cell: 919-434-7589
Email: Mailto:billott@theotts.org <billott(a)theotts.org>
Website: http://www.theotts.org
Profile: http://www.linkedin.com/in/wbott
On 3/24/19 7:44 PM, Gnucash Xboxboy Mageia wrote:
On Mon, Mar 25, 2019 at 1:50 AM bill Ott <billott(a)theotts.org> wrote:
Can you send me the results of the ifconfig on
the VM's host?
Reviewing I noticed. from below
"virbr0 is on 192.168.122.1" which is the wrong octal. it should be
192.168.1.XXX. It may be there because your VM is setting up its own DHCP.
But that begs the question of how you are reaching the 192.168.1.188 apache
interface on the VM.
If you ssh into the VM and issue an ifconfig there, what is its IP
address?
Thanks Bill: Ok, the Host IP has changed, because I didn't have a fixed
IP for
it: I've now sorted that. So here are the results of 'ifconfig'
enp5s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.106 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::62a4:4cff:fe38:82a9 prefixlen 64 scopeid 0x20<link>
ether 60:a4:4c:38:82:a9 txqueuelen 1000 (Ethernet)
RX packets 2173 bytes 521229 (509.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 176 bytes 19475 (19.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 100 bytes 8648 (8.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 100 bytes 8648 (8.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast
192.168.122.255
ether 52:54:00:da:32:4e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Regards,
Bill Ott
Home: 919-363-0031
Cell: 919-434-7589
Email: Mailto:billott@theotts.org <billott(a)theotts.org>
Website: http://www.theotts.org
Profile: http://www.linkedin.com/in/wbott
On 3/24/19 1:28 AM, Gnucash Xboxboy Mageia wrote:
On Thu, Mar 21, 2019 at 11:00 PM bill Ott <billott(a)theotts.org> wrote:
_______________________________________________
users mailing
listusers@lists.ledgersmb.orghttps://lists.ledgersmb.org/mailman/listinfo/users
Have you tried temporarily turning off SELinux
("setenforce 0"), then
trying to connect? After doing the test, turn SELinux back on with
"setenforce 1".
Thanks
Just tried that on the host OS with no change.
The debian VM doesn't have SElinux installed, as 'getenforce' and
'sestatus' return command not found.
Regards,
Bill Ott
Home: 919-363-0031
Cell: 919-434-7589
Email: Mailto:billott@theotts.org <billott(a)theotts.org>
Website: http://www.theotts.org
Profile: http://www.linkedin.com/in/wbott
On 3/21/19 3:40 AM, Xboxboy Mageia wrote:
Bill,
yes, sorry that is a typo: I meant http://192.168.1.118:5762/setup.pl
Regards,
Xboxboy
---------- Forwarded message ---------
From: bill Ott <billott(a)theotts.org>
Date: Thu, Mar 21, 2019 at 1:21 AM
Subject: Re: [ledgersmb-users] Fwd: Production Install, Networking and
Setup
To: Xboxboy Mageia <xboxboy.mageia(a)gmail.com>
http://192.168.1.*188*:5762/setup.pl???? Did you mean http://192.168.1.
*118:*5762/setup.pl?
Regards,
Bill Ott
Home: 919-363-0031
Cell: 919-434-7589
Email: Mailto:billott@theotts.org <billott(a)theotts.org>
Website: http://www.theotts.org
Profile: http://www.linkedin.com/in/wbott
On 3/19/19 9:47 PM, Xboxboy Mageia wrote:
Sorry Bill: I meant to send it to the list :-0
Please see the network info I've added, in response to both Bill and
Erik.
On Mon, Mar 18, 2019 at 6:45 PM Xboxboy Mageia <xboxboy.mageia(a)gmail.com>
wrote:
_______________________________________________
users mailing
listusers@lists.ledgersmb.orghttps://lists.ledgersmb.org/mailman/listinfo/users
Hello,
I was sick over Xmas, and since then business has been booming, only
now can I have a second look. Thank you all for you help.
On Thu, Jan 10, 2019 at 10:38 AM bill Ott <billott(a)theotts.org> wrote:
> Running "brctl show" w/o/ the quotes on the VM's host will show you
> the bridge and the interfaces that are connected to it. 'ifconfig" w/o the
> quotes on the VM's host will show you the all of interfaces.
>
brctl show
bridge name bridge id STP enabled
interfaces
virbr0 8000:525400da324e yes
virbr0-nic
ifconfig
enp5s0 is on 192.168.1.109
lo is on 127.0.0.1
virbr0 is on 192.168.122.1
(sorry can't ssh in at the moment, let me know if you need all the
details)
Might help chasing down the problem.
>
> Regards,
> Bill Ott
>
> Home: 919-363-0031
> Cell: 919-434-7589
> Email: Mailto:billott@theotts.org <billott(a)theotts.org>
> Website: http://www.theotts.org
> Profile: http://www.linkedin.com/in/wbott
>
> On 1/9/19 5:21 PM, Erik Huelsmann wrote:
>
> Hi,
>
> Ok, so the debian install went simply. I used debian 9 (Stretch),
>>> without a GUI. 'ip addr' gives 192.168.1.101, which sounds right, as
that's
>>> my lan, 192.168.1.X.
>>>
>>
>> I then followed the instructions on
>> https://apt.ledgersmb.org/index.html, but I installed version 1.5,
>> and did not add the 'test component', I don't know what that means,
sorry.
>>
>
> [snip]
>
>
>> I was able to add the DB admin user where the prompt comes up: Now do
>> I need to reset/config mysql's root user and password also?
>>
>> So from my desktop I tried to access via firefox
>> 192.168.1.101:5762/setup.pl, but it's unable to connect.
>>
>
> Ok. Are you able to ping that ip address from your desktop? That
> should indicate if you should expect to be able to connect to the web
> server as well.
>
>
> Yes, I can ping the debian VM with "ping 192.168.1.118"
I can access the default debian apache web server at 192.168.1.118, but
no luck with 192.168.1.188:5762/setup.pl
I have a functioning fedora os VM on 192.168.1.107 with nextcloud
working fine.
> I have the VM network set to bridged, networking is my downfall, and
>> the other thing I suspect is that I need to open the firewall for the
>> webserver.
>>
>
> Bridged sounds fine. quick question: Is the "eth0" (or enpXs0 with X a
> number) network on the VM's host part of the bridge? If not, you probably
> need to enable IP forwarding. Before we go that route, lets start by
> checking you can 'ping' the address though. (And: can you ping the host
> that the VM is running on?)
>
> I can ping the host with "ping 192.168.1.109"
>
>
>>
>> All advice appreciated.
>>
>
> Regards,
>
> --
> Bye,
>
> Erik.
>
> http://efficito.com -- Hosted accounting and ERP.
> Robust and Flexible. No vendor lock-in.
>
> _______________________________________________
> users mailing
listusers@lists.ledgersmb.orghttps://lists.ledgersmb.org/mailman/listinfo/users
>
> _______________________________________________
> users mailing list
> users(a)lists.ledgersmb.org
> https://lists.ledgersmb.org/mailman/listinfo/users
>
_______________________________________________
users mailing
listusers@lists.ledgersmb.orghttps://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________
users mailing
listusers@lists.ledgersmb.orghttps://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________
users mailing list
users(a)lists.ledgersmb.org
https://lists.ledgersmb.org/mailman/listinfo/users
1708
days inactive
1708
days old
0 comments
1 participants
participants (1)
-
Gnucash Xboxboy Mageia